Plumbing for Beginners: What You Need for Bathtub Installation
At This WebsiteWe've encountered the article involving A Step-by-Step Guide to Installing a Bathtub down the page on the net and figured it made good sense to discuss it with you on this site.
Installing a bath tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably hard project. If the old tub is easily obtainable, the project can move rapidly; if you have to open a wall surface to eliminate the old tub and position the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the new one. Make certain you have actually qualified on your own for the work as well as fit trying it. Instead of working with a professional to take control of a halfway-completed job, it is much better to consider utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This article will certainly aid you set up a new tub in your washroom if you have actually currently bought a brand-new bathtub and also don't need to change the setup of your previous water system pipelines.
Your tools and material list should comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted accessibility that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and also the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the called for placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bathtub until the level reads degree.
To set up faucets, fit the bottom of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Activate the supply of water and examine all joints and also brand-new pipework for leaks and also tighten them if essential. Fill the bath tub and additionally examine the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Planning for the Setup
Firstly, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to stop pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, leading to issues with dampness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can split rather early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up about Installing A Bathtub through a friend on another site. Please take a moment to share this blog posting if you enjoyed it. We treasure reading our article about Installing A Bathtub.
Stay calm, just ring.